Keep special masonry units separate from ordinary packs.
Publication and review
- Author
- Metandum Team
14 years of experience in digital web projects.
- Reviewer
- Metandum Team
14 years of experience in digital web projects.
- Published
- Last reviewed
- Last updated
Separate the Unit Roles
When you count masonry for a wall, keep ordinary units and specified special units on separate lines. A return unit and an approved cap unit may occupy positions within the same nominal total, but they do different jobs and are not interchangeable. Recording each role separately helps you carry the right count into purchasing, packing, and installation without treating every block as one undifferentiated quantity.
Start with the drawing, schedule, or project specification that identifies the special units. Confirm which positions call for each type, and preserve the specified names on your takeoff. The face you count also matters: count the unit positions shown for the relevant wall face or course, rather than adding other faces or nearby work by assumption. Keep structural requirements in their own specification review.
Confirm the Counted Face
Before entering a total, define what the total represents. It should cover the unit positions for the masonry area being scheduled, using the same scope and counted face as the special-unit positions. If a drawing shows returns, corners, or cap locations, check whether those positions are already included in the nominal total. This prevents subtracting a special position that was never part of the starting count.
Use the approved project documents to resolve unclear locations or quantities. A visual detail may show a cap or return, while the written schedule names the corresponding unit; compare both before you classify it. Do not infer that a unit is structurally adequate from its shape, label, or packaging. Structural suitability, reinforcement, bearing, and other design requirements remain governed by the applicable project documents.
Record Each Special Line
Enter each noninterchangeable type as its own line, with its specified position count and its stocked units per pack. Keep the role and package quantity attached to that line when you review the schedule. This makes it easier to see whether the count refers to return units or approved cap units, and whether the pack size belongs to that exact product type.
Check that your count describes positions, not packs or loose pieces already on site. A specified position count answers how many locations require that unit; units per pack answers how the supplier groups stock. Those are different measures. If packaging information is missing or outdated, verify it against current supplier information before ordering, and update the line without changing the project’s specified role.
Enter the Schedule Calculator
Use the Masonry Special Unit Schedule Calculator when you have a nominal total, an ordinary-unit pack size, and separate special-unit lines with known pack sizes. Enter the nominal position count under Total unit positions and the ordinary package quantity under Ordinary units per pack. Add one line for each specified unit type, entering its position count and the Units per pack value that applies to that type.
Keep the calculator inputs aligned with the same scope you checked on the drawings. Do not add a special unit twice, or subtract positions counted on another face. The calculator separates the remaining ordinary positions from each special line and calculates packs for each category. Review the output as a schedule, then confirm that the line names and package sizes still match the project and supplier records.
Read the Worked Schedule
In this example, the published schedule starts with 126 total unit positions and 44 ordinary units per pack. It lists 9 return units sold six per pack and 12 approved cap units sold eight per pack. The calculator leaves 105 ordinary positions, assigns 2 packs to the return line and 2 packs to the cap line, and returns 3 ordinary unit packs.
The counts reconcile because 126 positions minus 9 return positions and 12 cap positions leaves 105 ordinary positions. Pack totals are rounded up to whole packs: two six-unit packs cover nine return units, and two eight-unit packs cover twelve cap units. Three 44-unit ordinary packs cover 105 positions. Read these outputs by role; the results describe counted faces and stocked packaging, not structural approval.
Review Order Quantities
Compare the resulting pack counts with the way the supplier sells each unit. A pack count is a purchasing quantity, while a position count is the number of locations to fill. The difference between the number of positions and the number supplied reflects the package size and whole-pack rounding. Keep the surplus associated with its own unit type; do not use return units to make up a cap-unit shortage.
Before placing an order, check whether the site already has usable stock of the same specified unit and package type. If you account for inventory, document the quantity and subtract only stock that is confirmed to match the required unit. Keep damaged, unverified, or differently packaged pieces out of the available count until they are checked. Record any adjustment so the installer and purchaser can follow the same schedule.
Resolve Plan Changes
If a drawing revision changes a return, cap, or wall layout, revisit both the nominal total and the affected special-unit positions. A change to one line can alter the ordinary remainder as well as the pack count for that special type. Avoid updating only the ordinary quantity, because that can leave the scheduled total inconsistent with the revised plan.
For field changes, confirm which document or authorized direction governs before changing the takeoff. Mark the affected location and revise the relevant line instead of folding the change into a general allowance. If a replacement product has a different package size or specification, treat it as a distinct line until the project team confirms it can serve the intended role. Preserve the record of the previous count.
Finalize the Installation Handoff
Give the purchaser and installer a schedule that keeps ordinary positions, return positions, and approved cap positions visible as separate categories. Include the counted face or scope, the position count, and the units per pack for each line. This helps the crew identify the correct stock at delivery and reduces the chance that visually similar units are assigned to the wrong locations.
At delivery, compare labels and quantities with the schedule before distributing units around the work area. Keep packages identifiable by their specified role, and flag any mismatch for resolution before installation. The takeoff supports counting and ordering; it does not decide whether a unit meets structural or code requirements. Use the approved project documents for those decisions, and update the schedule when confirmed changes affect the work.
Questions about this guide
Should return units and approved cap units share one line?
No. Keep them separate because their roles and stocked pack sizes differ. Enter each specified position count with the package quantity for that particular unit type.
What does the ordinary unit pack result mean?
It is the number of whole ordinary-unit packs needed for the remaining ordinary positions after the specified special positions are subtracted from the total.
Should I count a special unit if it is on another face?
Only if that face is included in the nominal total and the takeoff scope. Confirm the counted face and avoid subtracting positions outside the total you entered.
Does the schedule confirm that a cap unit is structurally suitable?
No. The schedule organizes position counts and stocked packaging. Check structural suitability and other design requirements in the approved project documents.
Use the matching calculator
Updated . Reviewed . Methods and scope.