Equal outer ellipse dimensions with different inner openings: quantity checks.
Publication and review
- Author
- Metandum Team
14 years of experience in digital web projects.
- Reviewer
- Metandum Team
14 years of experience in digital web projects.
- Published
- Last reviewed
- Last updated
Compare the Same Outer Ellipse
Use the same 2.78 m by 1.64 m outer ellipse for both decorative borders, then subtract each border’s own inner opening. This answers the practical comparison: the smaller opening leaves more mounted surface to coat and crosses the next 0.50 L package threshold. In this example, the Ellipse Area Calculator gives the shared outer area as 3.58078730656 m².
That shared figure is a geometric baseline, not a measurement of every finished border. It assumes each outline is elliptical and that the listed full major and minor axes describe the actual profiles. If the mounted side has a lip, backing, raised edge, or other geometry, measure that surface separately before using its area as a paint input.
Measure Each Inner Opening
For the first border, enter the opening’s full major axis as 1.21 m and full minor axis as 0.73 m in the Ellipse Area Calculator. These are full widths across the opening, not radii. Its elliptical area is 0.693742197729 m². For the second border, enter 1.72 m and 0.84 m; its opening area is 1.13474326648 m².
Take both measurements on the face that defines the opening being subtracted. Keep the axes aligned with the opening’s widest and narrowest directions, and measure across its edge rather than along the decorative trim. If the opening is irregular or the edge is not elliptical, do not convert its bounding rectangle to an ellipse without fitting the measured profile.
Find the Coated Border Areas
Subtract each opening area from the shared outer area. The first border’s coated area is 3.58078730656 m² minus 0.693742197729 m², or 2.88704510883 m². The second border’s coated area is 3.58078730656 m² minus 1.13474326648 m², or 2.44604404009 m². These are the mounted face areas represented by the measured ellipse inputs.
A larger opening removes more area from the identical outer outline, so the second border leaves less face to coat. The comparison depends on the borders truly sharing the same outer dimensions and on paint going on the calculated mounted surface. If you plan to coat the reverse, edge, or a second face, measure and calculate those surfaces separately.
Compare Areas and Packages
The area difference is 0.44100106874 m², and it changes the purchase count under the stated paint assumptions. With the same coverage, two coats, 3% waste, and 0.50 L containers, the first border requires two packages while the second requires one. The table shows the separate opening and coating calculations so the package result can be checked against each area.
Treat the figures as outputs for these inputs, not a general coating instruction. The Ellipse Area Calculator supplies areas from full axes; the Paint Calculator then estimates volume using the entered coverage, coats, waste allowance, and container size. Actual use can differ if the measured mounted profile, product coverage, or the surface being painted differs from the case.
| Border case | Outer ellipse area | Inner opening axes | Opening area | Coated area | Paint required | Purchase result |
|---|---|---|---|---|---|---|
| First border | 3.58078730656 m² | 1.21 m × 0.73 m | 0.693742197729 m² | 2.88704510883 m² | 0.577409021767 L | 2 × 0.50 L containers |
| Second border | 3.58078730656 m² | 1.72 m × 0.84 m | 1.13474326648 m² | 2.44604404009 m² | 0.489208808017 L | 1 × 0.50 L container |
Enter the First Paint Case
For the first border, use the calculated coated area, 2.88704510883 m², as Surface area in the Paint Calculator. Enter Product coverage per unit as 10.3 m²/L, Number of coats as 2, Container size as 0.50 L, and Waste allowance as 3%. These entries describe this worked case; replace them with values that match your product label and plan when those differ.
The calculator returns 0.577409021767 L of paint required and rounds the purchase to two containers, or 1.00 L purchased. The remaining purchased surplus is 0.422590978233 L. Since the requirement exceeds one 0.50 L package, the purchase count moves to two. Do not mistake the surplus for an extra coat or assume it is exactly recoverable.
Enter the Second Paint Case
For the second border, start a separate Paint Calculator case using Surface area of 2.44604404009 m². Keep Product coverage per unit at 10.3 m²/L, Number of coats at 2, Container size at 0.50 L, and Waste allowance at 3%. A separate calculation keeps the opening comparison visible and prevents the two border areas from being treated as one combined surface.
The result is 0.489208808017 L required, which fits within one 0.50 L container. The displayed purchase is 0.50 L, with 0.010791191983 L surplus. That slim margin explains why the package decision is sensitive to measurements and assumptions. A small increase in area or waste, or lower actual coverage, could put the need above one package.
Check the Mounted Surface
Before buying, confirm which side is mounted and which side will receive coating. The subtraction above represents one elliptical face with an opening removed. If the visible border has a return edge, thickness, back face, or a profile that wraps around, those areas are not included in the face calculation. Measure additional paintable surfaces and add their areas if they are part of your project.
Check the outer and inner axes again after the border is fitted, especially if trim overlaps the opening or the visible perimeter differs from the piece’s overall dimensions. Where a profile departs from an ellipse, divide it into measurable shapes or trace the actual outline with an appropriate method. A rectangle around the object alone does not establish an elliptical area.
Decide Before You Purchase
Under the published worked example, choose two 0.50 L containers for the first border and one for the second. The whole-package threshold, rather than the 0.44100106874 m² area difference alone, changes the shopping decision. If you are coating both borders, calculate each as its own case and then total the required volume before rounding to the package size you can actually buy.
For a real project, verify the product’s stated coverage and decide whether its coverage applies to your material and finish. Keep the coats and waste allowance consistent with your plan, then recalculate if any input changes. Record the measured axes and which face they describe. Those checks make it clear whether a changed package count comes from geometry, coverage, or a revised coating plan.
Questions about this guide
Why does the border with the larger opening need fewer packages?
Both borders share the 3.58078730656 m² outer ellipse. The 1.72 m by 0.84 m opening removes 1.13474326648 m², leaving 2.44604404009 m² to coat. At the stated coverage, coats, waste, and 0.50 L package size, that case fits one container; the smaller opening leaves 2.88704510883 m² and needs two.
Should I include the trim edge or back of the border?
Include any edge or back that will receive coating, but calculate it as additional paintable area. The worked figures cover one mounted elliptical face after subtracting its opening; they do not include a return edge, thickness, or a second face.
Can I use the outside rectangle as the ellipse measurement?
No. Enter the measured full major and minor axes of the elliptical profile. A bounding rectangle does not define the ellipse area. If the outline is irregular, measure or fit that actual profile rather than treating the rectangle as an ellipse.
Could the second border still require two containers?
Yes, if its actual coated area or required paint volume rises above 0.50 L. The worked case leaves only 0.010791191983 L surplus, so recheck dimensions, coverage, coats, and waste allowance before relying on one package.
Use the matching calculator
Updated . Reviewed . Methods and scope.
Related decisions
How to measure and order: figured frame and decorative face coating quantities
Which measurements and product data prevent quantity mistakes for this job?
How to measure and order: surface preparation consumables
Which measurements and product data prevent quantity mistakes for this job?
Separate abrasive zones versus one pooled working area: quantity checks
A partially used abrasive sheet may be stranded in one work zone. Pooling area assumes its remaining usable life can transfer to another zone.
How to estimate paint for two coats
Does the product coverage figure already include the specified coats?