STOCK FIT

Corner bead piece — usable bead stock length scenarios.

How does changing usable bead stock length affect corner bead piece when the other inputs stay fixed?

What this decision changes

Full required pieces must fit usable stock. Aggregate area or length alone cannot prove a feasible cut or roll allocation. Method basis: Each corner is treated independently and offcuts are not reused. Confirm whether joining pieces is allowed for your specified bead.

The focus is usable bead stock length. All other shared inputs remain fixed for each evaluated range.

Stock pieces = Σ ceil(corner height / stock length) × countCorner Bead Piece Calculator

Evaluate your supplied alternatives

Start with your measured plan and selected product data. The initial values and range are illustrative. Each scenario changes only usable bead stock length; the other entered values stay fixed.

Display units

Measured plan and product inputs

Usable bead stock length

Where to get this value

Use the actual usable quantity or dimensions of the product you intend to buy. Check the label and the unit shown here.

Corner group 1

Corner height

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Identical corners

Corner group 2

Corner height

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Identical corners

Supplied comparison range for usable bead stock length

Lower supplied comparison value

Where to get this value

Use the actual usable quantity or dimensions of the product you intend to buy. Check the label and the unit shown here.

Upper supplied comparison value

Where to get this value

Use the actual usable quantity or dimensions of the product you intend to buy. Check the label and the unit shown here.

Nine evenly spaced values are evaluated. Whole counts are rounded to distinct integer scenarios. Values between the listed samples are not calculated.

9 evaluated scenarios

Baseline: Corner bead stock pieces — 6 pieces. Rejected combinations remain visible below.

Quantity to plot

Each bar is one actual calculated corner bead stock pieces. Horizontal values: usable bead stock length in m.

Usable bead stock length	Corner bead stock pieces	Change from baseline	Use this scenario
1.8 m	10 pieces	4 pieces	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 4.5 m
2.175 m	10 pieces	4 pieces	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 8.25 m
2.55 m	6 pieces	0 pieces	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 1.8 m
2.925 m	6 pieces	0 pieces	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 4.05 m
3.3 m	6 pieces	0 pieces	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 6.3 m
3.675 m	5 pieces	-1 piece	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 4.875 m
4.05 m	5 pieces	-1 piece	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 6.75 m
4.425 m	5 pieces	-1 piece	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 8.625 m
4.8 m	5 pieces	-1 piece	Open in calculator Exact quantity breakdown Installed corner length 13.5 m Unused stock length 10.5 m

Read the evaluated results

Look for jumps in purchased stock and rejected fits. The rows show actual evaluated allocations, not an assumption that every intermediate size will behave identically.

Replace every illustrative baseline measurement and selected product value with the inputs for your actual task.
Enter a comparison range on the focused input's stated unit and quantity basis.
Review rejected combinations and use the exact detail lines to distinguish measured demand from whole purchases.
Open an evaluated scenario in the full calculator to save its original inputs and quantity breakdown to a browser material project.

Keep the comparison within scope

Permitted orientation, complete-run requirements and reserved cut losses remain supplied inputs; sampled layouts do not promise a globally optimal cut plan.

Dimensions, layouts, rates and material properties are supplied by the user.

Does not select construction specifications or certify safety.

Only the listed samples are evaluated. Intermediate values, alternate constraints and global cutting optimality are not inferred from the graph.

Continue with this quantity method

Corner Bead Piece Calculator

Other independent input decisions

Prepare the actual material data

Read the measurement and purchase guides

Order corner beads from full-height cuts

Quantity method and illustrative scenarios checked 6 October 2026. Methods and scope.