Skip to main content

MEASURED QUANTITY SENSITIVITY

Planter board cut list — actual board face height scenarios.

How does changing actual board face height affect planter board cut list when the other inputs stay fixed?

What this decision changes

This measured quantity or supplied dimension enters the method on its stated unit basis. Other inputs stay fixed so its effect can be separated from net deductions, stock constraints or purchase rounding. Method basis: Rounds wall courses to whole boards but uses the specified finished height for capacity. Any trimmed top course is explicit; wall construction adequacy is excluded.

The focus is actual board face height. All other shared inputs remain fixed for each evaluated range.

Cut length = 2×courses×(outside length + outside width−2t)Specified Planter Board Cut List Calculator

Evaluate your supplied alternatives

Start with your measured plan and selected product data. The initial values and range are illustrative. Each scenario changes only actual board face height; the other entered values stay fixed.

Display units

Measured plan and product inputs

Outside length

m

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Outside width

m

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Specified wall height

m

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Actual board face height

m

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Actual wall board thickness

mm

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Identical containers

Supplied comparison range for actual board face height

Lower supplied comparison value

m

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Upper supplied comparison value

m

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Nine evenly spaced values are evaluated. Whole counts are rounded to distinct integer scenarios. Values between the listed samples are not calculated.

9 evaluated scenarios

Baseline: Total supplied wall-board cut length — 17.4 m. Rejected combinations remain visible below.

Quantity to plot

Each bar is one actual calculated total supplied wall-board cut length. Horizontal values: actual board face height in m.

Actual board face height	Total supplied wall-board cut length	Change from baseline	Use this scenario
0.12 m	29 m	11.6 m	Open in calculator Exact quantity breakdown Whole courses per wall 5 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.6 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.
0.145 m	23.2 m	5.8 m	Open in calculator Exact quantity breakdown Whole courses per wall 4 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.58 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.
0.17 m	17.4 m	0 m	Open in calculator Exact quantity breakdown Whole courses per wall 3 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.51 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.
0.195 m	17.4 m	0 m	Open in calculator Exact quantity breakdown Whole courses per wall 3 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.585 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.
0.22 m	17.4 m	0 m	Open in calculator Exact quantity breakdown Whole courses per wall 3 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.66 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.
0.245 m	17.4 m	0 m	Open in calculator Exact quantity breakdown Whole courses per wall 3 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.735 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.
0.27 m	11.6 m	-5.8 m	Open in calculator Exact quantity breakdown Whole courses per wall 2 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.54 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.
0.295 m	11.6 m	-5.8 m	Open in calculator Exact quantity breakdown Whole courses per wall 2 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.59 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.
0.32 m	11.6 m	-5.8 m	Open in calculator Exact quantity breakdown Whole courses per wall 2 Between-long-walls end-board cut 0.9 m Internal plan area 1.71 m² Specified-height internal capacity 0.855 m³ Actual stacked wall height before top trim 0.64 m Long walls run full outside length; end boards fit between them. Open-bottom geometry; support, fixing, lining and material suitability are not specified.

Read the evaluated results

Read calculated demand, whole purchases and exact detail lines separately. This specific input may change quantity continuously, cross a purchase step or make the stated geometry or stock fit invalid.

Replace every illustrative baseline measurement and selected product value with the inputs for your actual task.
Enter a comparison range on the focused input's stated unit and quantity basis.
Review rejected combinations and use the exact detail lines to distinguish measured demand from whole purchases.
Open an evaluated scenario in the full calculator to save its original inputs and quantity breakdown to a browser material project.

Keep the comparison within scope

Compare measurements or already specified alternatives. Quantity sensitivity does not establish material suitability or construction requirements.

Rounds wall courses to whole boards but uses the specified finished height for capacity. Any trimmed top course is explicit; wall construction adequacy is excluded.

Dimensions, quantities, prices, timing and product properties are supplied by you. This tool does not select construction specifications or assess structural, electrical or hydraulic suitability.

Only the listed samples are evaluated. Intermediate values, alternate constraints and global cutting optimality are not inferred from the graph.

Continue with this quantity method

Specified Planter Board Cut List Calculator

Other independent input decisions

Read the measurement and purchase guides

Use inside planter dimensions for fill and outside dimensions for board cuts

Quantity method and illustrative scenarios checked 6 October 2026. Methods and scope.