SUPPLIED LAYOUT INTERVALS

Centred cabinet handle hole coordinate — handle hole centre spacing scenarios.

How does changing handle hole centre spacing affect centred cabinet handle hole coordinate when the other inputs stay fixed?

What this decision changes

The chosen interval or repeat changes discrete positions, full rows or complete pattern cuts. It is different from a blanket percentage added to area. Method basis: Horizontal hole positions = front width/2 ± supplied hole-centre spacing/2; vertical position = supplied offset from top. Does not choose a handle, door construction, screw length or a suitable fixing location.

The focus is supplied handle hole centre spacing. All other shared inputs remain fixed for each evaluated range.

Horizontal hole positions = front width/2 ± supplied hole-centre spacing/2; vertical position = supplied offset from top.Centred Cabinet Handle Hole Coordinate Calculator

Evaluate your supplied alternatives

Start with your measured plan and selected product data. The initial values and range are illustrative. Each scenario changes only supplied handle hole centre spacing; the other entered values stay fixed.

Display units

Measured plan and product inputs

Measured front width

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Measured front height

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Supplied handle hole centre spacing

Supplied vertical hole offset from top

Identical fronts

Supplied comparison range for supplied handle hole centre spacing

Lower supplied comparison value

Upper supplied comparison value

Nine evenly spaced values are evaluated. Whole counts are rounded to distinct integer scenarios. Values between the listed samples are not calculated.

9 evaluated scenarios

Baseline: Supplied handle holes — 6 holes. Rejected combinations remain visible below.

Quantity to plot

Each bar is one actual calculated first hole from left. Horizontal values: supplied handle hole centre spacing in mm.

Supplied handle hole centre spacing	First hole from left	Change from baseline	Purchase result	Use this scenario
76.8 mm	0.2616 m	0.0256 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.2616 m Second hole from left 0.3384 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.
92.8 mm	0.2536 m	0.0176 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.2536 m Second hole from left 0.3464 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.
108.8 mm	0.2456 m	0.0096 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.2456 m Second hole from left 0.3544 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.
124.8 mm	0.2376 m	0.0016 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.2376 m Second hole from left 0.3624 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.
140.8 mm	0.2296 m	-0.0064 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.2296 m Second hole from left 0.3704 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.
156.8 mm	0.2216 m	-0.0144 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.2216 m Second hole from left 0.3784 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.
172.8 mm	0.2136 m	-0.0224 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.2136 m Second hole from left 0.3864 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.
188.8 mm	0.2056 m	-0.0304 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.2056 m Second hole from left 0.3944 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.
204.8 mm	0.1976 m	-0.0384 m	6 holes	Open in calculator Exact quantity breakdown First hole from left 0.1976 m Second hole from left 0.4024 m Both holes from top 0.1 m Positions are relative to the measured front edges. Hole diameter, pilot depth and suitability of this location are not chosen.

Read the evaluated results

Use the evaluated count steps to see when another row, column, drop or position enters the stated layout.

Replace every illustrative baseline measurement and selected product value with the inputs for your actual task.
Enter a comparison range on the focused input's stated unit and quantity basis.
Review rejected combinations and use the exact detail lines to distinguish measured demand from whole purchases.
Open an evaluated scenario in the full calculator to save its original inputs and quantity breakdown to a browser material project.

Keep the comparison within scope

Compare intervals already permitted by your plan or product. No safe spacing, structural layout or fixing requirement is chosen.

Does not choose a handle, door construction, screw length or a suitable fixing location.

Only the listed samples are evaluated. Intermediate values, alternate constraints and global cutting optimality are not inferred from the graph.

Continue with this quantity method

Centred Cabinet Handle Hole Coordinate Calculator

Read the measurement and purchase guides

Quantity method and illustrative scenarios checked 6 October 2026. Methods and scope.