MetandumFREE TOOLS. NO SUBSCRIPTION.Find a calculator My projects
MEASUREMENTS AND PURCHASE DECISIONS

Keep measured unusable board zones separate from end trimming.

Publication and review

Author
Metandum Team

14 years of experience in digital web projects.

Reviewer
Metandum Team

14 years of experience in digital web projects.

Published
Last reviewed
Last updated

Measure the Whole Section

When a rectangular surface has an opening inside it, start by measuring the full outer rectangle. Measure its length and width between the outside edges, using the same unit for both. In this example, the section is 1.644 m long and 1.182 m wide. Enter those measurements in the Square Footage & Area Calculator under Length and Width, with the units shown as m.

The calculator first establishes the area of the complete rectangle, as if the opening were still covered. For this section, Area before exclusions is 1.943208 m². Keep this starting measurement clear: it describes the full surface boundary, while the opening is handled separately. Do not shorten the outside length or width to account for an opening inside the rectangle. If you are measuring a floor or wall, identify the same outside edges at both ends so the rectangle reflects the section you intend to calculate.

Measure the Inside Opening

Next, measure the opening itself. For a rectangular opening, take its length and width between the inside edges. In this example, an opening measuring 0.61 m by 0.60 m has an area of 0.366 m². Enter that value as Area to exclude in the calculator. The example’s entry is 0.366 m².

The calculator case provides the excluded area rather than separate opening dimensions, so the two opening measurements here show one way that area could be obtained. If the opening is an irregular shape, measure or calculate its area using an appropriate method before entering it. For multiple openings, add their areas when they do not overlap, then enter the combined area. Check that each opening lies within the measured outer rectangle and that no opening has been counted twice.

Read the Net Surface Area

With the full rectangle and opening area entered, the calculator subtracts the exclusion from the area before exclusions. In this example, 1.943208 m² minus 0.366 m² gives a net surface area of 1.577208 m². This is the surface area remaining after the internal opening is removed from the calculation.

The result answers an area question: how much surface remains within the measured outer boundary? It can help describe the area to cover or finish, provided the opening is genuinely outside that work. The calculator also reports one section counted. That count describes the entered section; it does not say how many stock pieces, boards, tiles, or other rectangular items will be needed. When sharing the result with someone planning the work, include the outer dimensions and opening area so the net figure has context.

Keep Area and Piece Yield Separate

A net area is not a piece count. Real rectangular pieces have fixed dimensions, and their placement depends on the layout across the whole section. Pieces may cross the opening, need cuts around its edges, or leave offcuts that cannot fit elsewhere. The net surface area removes the opening’s area mathematically, but it does not arrange pieces on the remaining surface.

For that reason, do not divide 1.577208 m² by a piece’s area and treat the quotient as a reliable yield. That calculation might suggest a rough area equivalent, but it cannot account for where cuts fall or whether leftovers can be reused. For an actual placement plan, consider the full outer rectangle and the opening’s position and bounds. Marking both on a sketch can show where full pieces fit, where cuts are needed, and whether an offcut can serve another edge. The calculator result is net area, not a guarantee of how many pieces to buy or install.

Check the Shape and Units

Before relying on the result, check that the section can reasonably be represented by one rectangle and that the opening area belongs inside it. Confirm that Length and Width are both entered in m, and that Area to exclude is entered in m². The calculator’s output is also in m², so the values in this example can be compared directly.

If the outer boundary has several distinct shapes, treating it as one rectangle may include areas that are not actually present. Break the work into rectangular sections when that better represents the measured surface, and account for openings within the relevant section. For multiple openings, combine their areas without overlap. A misplaced decimal or a unit mismatch changes the subtraction, so recheck the measured boundaries and entered area before using the net result. The calculation is meaningful only when the outer dimensions and exclusion describe the same section.

Use the Result for Area Planning

Use 1.577208 m² as the example’s remaining surface area after excluding the 0.366 m² opening from the 1.943208 m² outer rectangle. This net figure can inform an area estimate for work that covers only the surface around the opening. Keep the units beside the number in your notes so it is not mistaken for a length or a piece quantity.

For rectangular pieces, continue with a separate placement plan based on the actual piece dimensions and the measured outer and inner bounds. Consider how the layout meets the opening edges and where cut pieces or offcuts could fit. For instance, shifting a starting edge may change the sizes of cuts around the opening even though the net area stays fixed. The area result provides an input to that planning, while the chosen piece size and arrangement determine the placement count. Those details are not part of this example’s calculator entries.

Record Both Measurements

Keep the outer rectangle and the opening measurements together in your notes. For this example, record an outer section of 1.644 m by 1.182 m, an internal opening of 0.61 m by 0.60 m, and the resulting net surface area of 1.577208 m². The opening dimensions produce the entered exclusion of 0.366 m².

This record makes it easier to revisit the calculation if the layout or measurements change. If the opening moves but stays the same size, the net area remains the same, yet piece placement may change because cuts could fall in different places. If the opening size changes, update its area and recalculate. When the work area is divided into sections, label each outer rectangle and its opening so an exclusion is subtracted from the correct section. Keep area calculations and layout decisions distinct: one reports remaining surface, and the other considers how actual rectangular pieces fit.

Questions about this guide

How do I check whether the opening area is plausible?

For a rectangular opening, multiply its measured length by width. In this example, 0.61 m × 0.60 m = 0.366 m², which is the entered Area to exclude.

How should I handle two openings in the same section?

Add their areas if they do not overlap, then enter the combined area as Area to exclude. Keep the measured openings inside the outer rectangle.

What should I sketch before estimating rectangular piece placement?

Sketch the 1.644 m by 1.182 m outer bounds and mark the opening’s measured position and bounds. Then use the actual piece dimensions to consider cuts and reusable offcuts.

If the opening shifts, do I need to recalculate net area?

If it stays the same size and remains inside the same outer section, the net area stays 1.577208 m² in this example. Reconsider placement because the cuts may change.

Use the matching calculator

Updated . Reviewed . Methods and scope.

Related decisions

Connected work guides and comparisons

Browse all work types

Collect your material inputs

Browse material preparation sheets

Evaluate your own supplied alternatives

Browse quantity scenarios