Lumber calculators.
Distinguish physical timber volume, board feet, whole stock items and studs counted from an existing layout.
Choose a work subcategory
Board Foot Calculator
Calculate board feet from the actual dimensions and number of boards.
Open calculatorLumberLumber Purchase List Calculator
Keep different board sizes separate while estimating purchase counts and volume.
Open calculatorLumberWall Stud Quantity Calculator
Count studs in uninterrupted spans and add the opening and corner details from your plan.
Open calculatorLumberTimber End Trim Volume Calculator
Separate purchased timber volume from usable volume after a stated end-trim allowance on each piece.
Open calculatorLumberBoard Resaw Yield Calculator
Count finished equal-thickness boards from a supplied blank, saw kerf and surfacing allowance.
Open calculatorLumberSheet Strip Rip Calculator
Calculate long strips ripped from sheet width after total edge trim and saw kerf.
Open calculatorLumberMitered Frame Cut List Calculator
Measure the long-point cut lengths for a rectangular surround with supplied visible face width.
Open calculatorLumberSupplied Cabinet Door Overlay Calculator
Calculate equal door leaf dimensions from an opening and overlays or reveals already chosen in your plan.
Open calculatorLumberEqual Drawer Front Grid Calculator
Divide a specified cabinet face into equal drawer fronts after outer reveals and gaps between fronts.
Open calculatorLumberMeasured Exclusion Board Piece Yield Calculator
Count equal pieces that fit the usable intervals of one board after measured excluded zones and per-piece cut loss.
Open calculatorLumberDrawer Box Panel Cut List Calculator
Generate five panel blanks for an explicitly supplied drawer-box arrangement.
Open calculatorLumberFace Frame Cut List Calculator
Deduct continuous stile widths from the horizontal rail cut list.
Open calculatorLumberEqual Compartment Divider Layout Calculator
Distribute an existing shelf opening into equal compartments after divider deductions.
Open calculatorLumberTimber Glue-Up Width Calculator
Account for preparation on every board before trimming a specified assembled panel.
Open calculatorLumberPolygonal Stave Ring Geometry Calculator
Measure the inside and outside widths of an already specified polygonal stave ring.
Open calculatorLumberAngled End Cut Blank Calculator
Translate a supplied short edge and two end angles into long-edge cut blanks.
Open calculatorLumberSpecified Planter Board Cut List Calculator
Coordinate supplied wall board cuts with the inside dimensions used for fill.
Open calculatorLumberSupplied Cabinet Hinge and Plate Pack Calculator
Keep supplied hinges and matching mounting plates as separate product quantities and pack orders.
Open calculatorLumberDrawer Slide Pair versus Single Rail Pack Calculator
Translate supplied drawer slide pairs into supplier packs sold as complete pairs or individual rails.
Open calculatorLumberCentred Cabinet Handle Hole Coordinate Calculator
Locate two supplied horizontal handle holes on the centre of a measured front and count repeated hole pairs.
Open calculatorLumberSupplied Shelf Pin Grid and Purchase Pack Calculator
Count rows in a supplied pin-hole grid while ordering pins only for the shelves you already specified.
Open calculatorLumberCabinet Back Panel Rebate Blank Sheet Calculator
Expand a measured clear back opening by supplied insertion on each edge, then allocate complete back panel blanks.
Open calculatorLumberSpecified Paired Veneer Leaf Bundle Calculator
Order even-numbered leaf groups for each face using a supplied paired layout, preserving whole leaf length and supplier bundles.
Open calculatorConnect these calculations
Measure and check your purchase assumptions
How to measure and order: furniture hardware packs and supplied panel details
Which measurements and product data prevent quantity mistakes for this job?
Read guideguideComplete slide pair packs versus individual rail packs: quantity checks
A pack count is meaningless until its unit basis is known. One pair contains two matching rails; one individual rail is not a complete pair.
Read guideguideRead between-sides dimensions in a drawer panel list
Does an outside width belong on a front cut that fits between side panels?
Read guidecomparisonKeep butt-joint face-frame cuts separate from miter long points
Do rails fit between continuous stiles or meet at mitered corners?
Read guidetroubleshootingDeduct divider thickness before dividing equal clear openings
Why are completed compartments narrower than width divided by count?
Read guideguideSeparate per-board preparation from final panel trim
Does a repeated edge loss need to be applied before assembling panel width?
Read guideguideRead inside face distance rather than inside corner radius for staves
Does the inside ring dimension end at a flat face or a vertex?
Read guideguideState end-cut angles relative to square before calculating blanks
Is a supplied angle measured from a square end or from the board edge?
Read guideguideCheck actual dimensions before treating board feet as physical timber volume
Are the listed board dimensions actual measurements or nominal labels?
Read guideguidePurchased stock length is not installed finished length
Which losses have already been included in the installed cut list?
Read guideguideTranslate a supplied opening into overlay or inset leaf dimensions
Where does the centre gap belong when two equal doors share one opening?
Read guidetroubleshootingSubtract shared face reveals before dividing drawer fronts
Why can dividing cabinet height by drawer count make the fronts too tall?
Read guideguideKeep measured unusable board zones separate from end trimming
Why does total remaining board length overstate equal-piece yield?
Read guideguideAccount for resaw kerf and surfacing allowances
Why is blank thickness divided by finished thickness an optimistic resaw yield?
Read guideguideDistinguish sheet ripping from rectangle nesting
Which cutting model should be used for long strips?
Read guideguideRead long-point dimensions in a mitered frame
Why are mitered cut lengths larger than the inside opening?
Read guide