MetandumFREE TOOLS. NO SUBSCRIPTION.Find a calculator My projects
COMPARE THE SUPPLIED SCENARIOS

Keep butt-joint face-frame cuts separate from miter long points.

Publication and review

Author
Metandum Team

14 years of experience in digital web projects.

Reviewer
Metandum Team

14 years of experience in digital web projects.

Published
Last reviewed
Last updated

Choose the dimension boundary first

A butt-joint face frame and a mitered surround can enclose a similar opening while needing different cut lengths. The face-frame model measures the outside frame width and height. Its stiles run the full height, and each horizontal rail fits between them. The miter model starts with the inside opening and extends each piece to its long point by adding twice the face width. Those measurements describe different boundaries of the finished assembly. Before choosing a calculator, identify whether the drawing dimensions show the outside of a frame or the clear opening, and confirm which members continue through the corners. Transferring an opening dimension directly into an outside-width formula can create a misleading cut list.

Read the between-stiles frame example

The supplied face-frame case uses a 1 m outside width, 2 m outside height, 0.1 m stile face width, 0.1 m rail face width, 0.02 m thickness and two horizontal rails. Each rail spans 1 m minus the two stile widths, giving 0.8 m. The calculator totals the two full-height stiles and both rails at 5.6 m of member length. Its result lines also report a 1.8 m combined opening height and 0.0112 m³ net material volume. The volume depends on the entered member dimensions and thickness. This is an illustrative cut-list arithmetic case; it does not establish stock lengths or a joinery design. The check records the calculated outputs from the frame engine.

Trace the mitered surround separately

A mitered frame uses the inside opening as its starting measurement. In the companion example, the opening is 1 m wide by 2 m high and the face is 0.1 m. Each horizontal piece reaches a 1.2 m long point, while each vertical piece reaches 2.2 m. Across the four pieces, combined long-point length is 6.8 m. These dimensions assume a flat rectangle with four 45-degree miters, as the tool specifies. A drawing that gives outside dimensions needs those converted to an opening measurement before entering this model. The example is not a second answer to the face-frame cut list; it represents a different corner arrangement and reference boundary.

Compare like parts across proposals

When comparing two plans, separate vertical stiles, horizontal rails and mitered sides instead of comparing only total stock length. The face-frame formula counts the long stiles continuously and shortens rails to fit between them. The picture-frame formula extends each member to an outer long point around a clear opening. A lower total from one result does not mean that its design uses less material for an equivalent assembly, because the joinery and dimensions differ. Check that the proposed parts actually match the selected calculator’s assumptions. If a drawing uses half-laps, overlapping corners, unequal members or a continuous profile, the models do not describe that construction simply by adjusting the width inputs.

Keep rail count and rail width distinct

The face-frame calculator asks for the number of horizontal rails and their face width as separate values. The count changes total member length, while rail width contributes to the remaining combined opening height and net material volume. Enter the number shown in the drawing, not the number of openings or shelves unless each corresponds to a rail. Stile width is applied on both sides of the outside frame width to obtain the between-stiles rail cut. The supplied thickness contributes to volume but does not change the cut-length expression. These fields represent different geometric roles; a value placed in the wrong field can still produce a number, so review the labels against the cut list before relying on it.

Account for stock and saw cuts afterward

The calculators report member dimensions or combined cut length. They do not nest pieces into available board stock, include saw kerf or decide how much extra length to retain for end trimming. A stock plan requires the actual board lengths, defects, grain direction and cutting sequence. Keep those decisions in a separate layout so a cut list is not mistaken for a purchase quantity. If the shop intends to use a rough-sawn board, distinguish its nominal label from its measured finished dimensions before entering member widths and thickness. Neither model assesses the strength of a joint, fastener spacing, panel movement or frame loading. Follow the project drawing and appropriate woodworking guidance for those construction decisions.

Use consistent units and labels

Read the units displayed beside the fields before transferring dimensions from a drawing. A millimeter dimension needs conversion when the selected input expects meters; entering the original number does not change that field's unit. Use the application's unit controls where available and carry the displayed result units into the cut list. Label each result as outside-frame members or miter long points so another person can tell which model produced it. The material-volume line is separate from the member-length total and uses its own displayed volume unit. Retaining those labels prevents a volume figure from being read as board length or a single frame's total from being carried into a multiple-frame order. Record the drawing's original units alongside the converted measurements.

Preserve the drawing with the cut list

Save the relevant drawing, dimension boundary, member sizes, quantity and calculator output together. If an opening changes, update the miter dimensions from the revised clear opening; if the outside face-frame size changes, recompute rails from the new width and stile sizes. Keep earlier results when a proposal is revised so each cut list remains linked to the design version that produced it. Before cutting, check the actual stock and confirm the chosen corner joinery with the person building the frame. The arithmetic describes supplied dimensions under the tool’s assumptions. It does not approve a structural frame, select material grade or confirm that the finished opening will fit another assembly. Label the cut list with its drawing revision and measurement units. Compare the saved endpoints with the shop drawing.

Questions about this guide

What dimension boundary does each frame calculator use?

The face-frame model starts from the outside frame width and height, with full-height stiles and rails between them. The mitered-frame model starts from the clear opening and extends each piece to its long point.

What does the one-meter-by-two-meter face-frame example return?

With 0.1-meter stile and rail faces, 0.02-meter thickness, and two rails, each between-stile rail is 0.8 meters. Total member length is 5.6 meters and net volume is 0.0112 cubic meters.

How long are the mitered pieces for the same clear opening?

For a 1-by-2-meter opening and 0.1-meter face, the miter tool returns 1.2-meter horizontal and 2.2-meter vertical long points, totaling 6.8 meters across four pieces.

Can the longer total be used to decide which frame uses less material?

Not without comparing equivalent assemblies. One model counts continuous stiles with between-stiles rails; the other counts four mitered pieces from the clear opening. Their boundaries and joinery differ.

Use the matching calculator

Updated . Reviewed . Methods and scope.

Related decisions

Connected work guides and comparisons

Browse all work types

Collect your material inputs

Browse material preparation sheets

Evaluate your own supplied alternatives

Browse quantity scenarios