DEDUCTIONS AND EXISTING STOCK

Mitered frame cut list — inside opening width scenarios.

How does changing inside opening width affect mitered frame cut list when the other inputs stay fixed?

What this decision changes

A known internal space, existing stock or shared quantity must enter the correct subtraction or eligibility step rather than being counted as new material. Method basis: Assumes four 45-degree miters in a flat rectangular frame. Does not compute stock nesting, clamping or joint strength.

The focus is inside opening width. All other shared inputs remain fixed for each evaluated range.

Long point lengths = inside dimension + 2 × frame face widthMitered Frame Cut List Calculator

Evaluate your supplied alternatives

Start with your measured plan and selected product data. The initial values and range are illustrative. Each scenario changes only inside opening width; the other entered values stay fixed.

Display units

Measured plan and product inputs

Inside opening width

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Inside opening height

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Frame face width

Identical frames

Supplied comparison range for inside opening width

Lower supplied comparison value

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Upper supplied comparison value

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Nine evenly spaced values are evaluated. Whole counts are rounded to distinct integer scenarios. Values between the listed samples are not calculated.

9 evaluated scenarios

Baseline: Combined long-point cut length — 6.8 m. Rejected combinations remain visible below.

Quantity to plot

Each bar is one actual calculated combined long-point cut length. Horizontal values: inside opening width in m.

Inside opening width	Combined long-point cut length	Change from baseline	Use this scenario
0.6 m	6 m	-0.8 m	Open in calculator Exact quantity breakdown Horizontal piece long point 0.8 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2
0.725 m	6.25 m	-0.55 m	Open in calculator Exact quantity breakdown Horizontal piece long point 0.925 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2
0.85 m	6.5 m	-0.3 m	Open in calculator Exact quantity breakdown Horizontal piece long point 1.05 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2
0.975 m	6.75 m	-0.05 m	Open in calculator Exact quantity breakdown Horizontal piece long point 1.175 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2
1.1 m	7 m	0.2 m	Open in calculator Exact quantity breakdown Horizontal piece long point 1.3 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2
1.225 m	7.25 m	0.45 m	Open in calculator Exact quantity breakdown Horizontal piece long point 1.425 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2
1.35 m	7.5 m	0.7 m	Open in calculator Exact quantity breakdown Horizontal piece long point 1.55 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2
1.475 m	7.75 m	0.95 m	Open in calculator Exact quantity breakdown Horizontal piece long point 1.675 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2
1.6 m	8 m	1.2 m	Open in calculator Exact quantity breakdown Horizontal piece long point 1.8 m Horizontal pieces 2 Vertical piece long point 2.2 m Vertical pieces 2

Read the evaluated results

Watch the net requirement and actual order separately. Invalid rows identify combinations that cannot satisfy the method's geometric or stock-basis constraints.

Replace every illustrative baseline measurement and selected product value with the inputs for your actual task.
Enter a comparison range on the focused input's stated unit and quantity basis.
Review rejected combinations and use the exact detail lines to distinguish measured demand from whole purchases.
Open an evaluated scenario in the full calculator to save its original inputs and quantity breakdown to a browser material project.

Keep the comparison within scope

The supplied cavity, exclusion or stock eligibility must already be valid; the result does not select a safe shell, opening or construction detail.

Dimensions, layouts, rates and material properties are supplied by the user.

Does not select construction specifications or certify safety.

Only the listed samples are evaluated. Intermediate values, alternate constraints and global cutting optimality are not inferred from the graph.

Continue with this quantity method

Mitered Frame Cut List Calculator

Other independent input decisions

Prepare the actual material data

Read the measurement and purchase guides

Quantity method and illustrative scenarios checked 6 October 2026. Methods and scope.