Read long-point dimensions in a mitered frame.
Publication and review
- Author
- Metandum Team
14 years of experience in digital web projects.
- Reviewer
- Metandum Team
14 years of experience in digital web projects.
- Published
- Last reviewed
- Last updated
Opening Size Versus Outside Length
When you cut a picture frame with 45-degree miters, the inside opening and the finished outside dimensions describe different edges of the frame. The opening is measured between the inside edges of the assembled pieces. A long-point measurement runs between the farthest tips at the outside corners. Since the frame has width, the long-point length must extend beyond the opening measurement.
Keep those measurements separate as you plan the cuts. Enter the desired inside opening dimensions in the Mitered Frame Cut List Calculator, then enter the actual face width of the profile you are using. The calculator uses that width to determine how far each piece extends past the opening at both ends. A finished outside measurement is useful for checking the assembled frame, but it is not a substitute for the opening size.
The Published Two Frame Example
In this example, the requested inside opening is 0.507 m wide by 0.368 m high. The frame face width is 0.047 m, and the number of identical frames is 2. These are the entries for the Mitered Frame Cut List Calculator. The stated dimensions describe the clear opening, while the face width describes the front strip of material visible around it.
For this entry, the calculator reports a horizontal piece long point of 0.601 m and a vertical piece long point of 0.462 m. It calls for 4 horizontal pieces and 4 vertical pieces across both frames, and gives a combined long-point cut length of 4.252 m. Read the piece lengths as the long-point length for each individual rail or stile. The combined length is the sum across the full two-frame cut list.
How Face Width Affects Each Cut
The profile face width adds to the outside span at both ends of a horizontal or vertical piece. In the example, 0.507 m of opening width plus 0.047 m of face width at each side gives a horizontal long point of 0.601 m. The height works the same way: 0.368 m plus 0.047 m at the top and 0.047 m at the bottom gives a vertical long point of 0.462 m.
This relationship depends on the face width of the profile actually being cut. If you use a different molding, measure its face width and enter that number instead of carrying over the example's 0.047 m. A wider face increases the long-point dimension even when the opening stays the same. The arithmetic is a way to understand the calculator's result and catch a mistaken input; it does not change the specified opening.
Check the Forty Five Degree Miters
For matching 45-degree picture-frame miters, the two cut ends meet at each corner, and the profile's face width spans the distance between its inside and outside edges. Along a horizontal piece, that face width contributes once at the left end and once at the right end to the long-point span. Along a vertical piece, it contributes once at the top and once at the bottom. That is why the outside long-point dimension adds twice the face width to the corresponding opening dimension.
Use this geometry as a quick reasonableness check. The horizontal long point should be greater than the inside opening width, and the vertical long point should be greater than the inside opening height. In the published example, those increases are 0.094 m in each direction, which is two times the 0.047 m face width. If your profile has a different visible width, the increase should change with it.
Read the Cut List Counts
The calculator result is for two identical frames, not one. Each frame needs two horizontal pieces and two vertical pieces. Across two frames, that becomes 4 horizontal pieces and 4 vertical pieces. Each of the four horizontal cuts has a 0.601 m long-point length, and each of the four vertical cuts has a 0.462 m long-point length.
The reported combined long-point cut length, 4.252 m, is consistent with those quantities: four horizontal lengths total 2.404 m, and four vertical lengths total 1.848 m. Together they equal 4.252 m. Use the individual piece lengths when laying out cuts, and use the combined value to understand the total length represented by the list. It is a sum of cut lengths, rather than a separate dimension for any one side of a frame.
Measure Before Entering Values
Measure the opening you want the finished frame to surround, then determine whether that measurement is its inside width and height. Measure the frame face across the front from the edge that will face the opening to the outer edge. Enter those values in the calculator fields labeled “Inside opening width,” “Inside opening height,” and “Frame face width.” Set “Identical frames” to the number of matching frames you are cutting.
Keep the units consistent with the field entries and read the returned lengths in the displayed unit. The example uses meters throughout. Do not treat the published dimensions as default sizes for your project: they describe one particular opening, profile width, and quantity. If you change any of those inputs, use the calculator's new piece lengths and counts for your own cut list.
Compare Cuts With the Frame
Before cutting all the pieces, compare the planned long points with the outside dimensions you expect after assembly. In the example, the horizontal outside span from long point to long point is 0.601 m, and the vertical span is 0.462 m. The inside opening remains 0.507 m by 0.368 m. That distinction helps explain why a frame made for a given opening occupies more space on the wall or shelf.
Check that the actual profile face width matches the value entered and that the opening measurements were not entered as outside dimensions. Also confirm the number of identical frames so the piece counts apply to your project. If a measured frame face differs, recalculate before using the cut lengths. The cut list describes the requested geometry for matching 45-degree corners; it does not make claims about the material's strength or how the frame will be used.
Questions about this guide
Which dimensions should I enter for the opening?
Enter the clear inside width and height you want within the assembled frame. Do not enter the outside long-point dimensions in the inside-opening fields.
How do I measure frame face width?
Measure across the visible front face from its inside edge to its outside edge. Use the actual profile you plan to cut; the example's 0.047 m is specific to that case.
Why are the long points larger than the opening?
At 45-degree corners, the face width extends beyond the opening at both ends of each piece. The long-point dimension adds twice the face width to the corresponding opening dimension.
How many pieces does the example require per frame?
Two horizontal and two vertical pieces per frame. For the calculator's 2 identical frames, the result is 4 horizontal pieces and 4 vertical pieces.
Use the matching calculator
Updated . Reviewed . Methods and scope.
Related decisions
Keep butt-joint face-frame cuts separate from miter long points
Do rails fit between continuous stiles or meet at mitered corners?
State end-cut angles relative to square before calculating blanks
Is a supplied angle measured from a square end or from the board edge?
Simple picture frame: measured dimensions and layout checks
Simple picture frame: which measured inputs, documented product distinctions and complete purchase units answer this layout question?
Simple picture frame: documented options and quote comparison
Simple picture frame: which measured inputs, documented product distinctions and complete purchase units answer this comparison question?