MetandumFREE TOOLS. NO SUBSCRIPTION.Find a calculator My projects
FIND THE QUANTITY ERROR

Subtract shared face reveals before dividing drawer fronts.

Publication and review

Author
Metandum Team

14 years of experience in digital web projects.

Reviewer
Metandum Team

14 years of experience in digital web projects.

Published
Last reviewed
Last updated

Start With the Face Envelope

To size five equal drawer fronts, subtract the planned reveals and the four gaps from the fixed outside face height, then divide what remains by five. This gives front heights for the stated opening and layout. It does not establish drawer-box dimensions or confirm that a particular slide will fit; those decisions depend on separate hardware and clearance checks.

In this example, the fixed face envelope is 1.137 m high and 0.728 m wide. Treat those as the outside dimensions available to the full arrangement, not as dimensions for one drawer. Keep the envelope fixed while you plan the visible reveals. If the cabinet opening or face envelope changes later, recalculate before cutting, because every front height depends on the same shared height.

Record Each Planned Reveal

The example uses a 12 mm top reveal and a 16 mm bottom reveal. Those allowances are intentionally unequal, so do not average them or assume the front stack is centered. Their combined height is 28 mm. Measure each allowance from the relevant outside edge to the nearest front edge, using consistent reference points on the cabinet and the finished face.

At the two outside sides, the planned reveal is 9 mm at each side. Together they consume 18 mm of the 0.728 m overall face width, leaving 0.710 m for each front's width. Paired side reveals matter because the width belongs to one front extending across the opening; they are not extra vertical space and should not enter the height subtraction.

Count Gaps Between Fronts

Five fronts create four internal gaps, because a gap sits between neighboring fronts. In the example, each gap is 14 mm, so the gaps use 56 mm in total. Do not subtract five gaps just because there are five fronts. That would remove an extra 14 mm and make each calculated front too short.

Sketch the stack in order before entering values: top reveal, front, gap, front, gap, front, gap, front, gap, front, bottom reveal. This quick count catches a common layout mistake. The top and bottom allowances occur once each; the internal gap occurs once between each adjacent pair. The outside side reveals belong to the width calculation only.

Subtract Before Dividing

The available front height is the 1.137 m envelope minus the 12 mm top reveal, the 16 mm bottom reveal, and four 14 mm gaps. Convert millimeters to meters before combining values: 0.012 m, 0.016 m, and 0.056 m. The remainder is 1.053 m. This is the combined height available to all five fronts, not the height of one front.

Divide that 1.053 m remainder by five equal fronts to get 0.2106 m per front. Dividing the full envelope first would assign some reveal and gap space to the fronts, producing a result that cannot fit the planned stack. Keeping the subtraction visible also makes it easier to revise one allowance or gap later and understand why the front size changed.

Check the Face Width After Reveals

The Equal Drawer Front Grid Calculator reports Each drawer front height as 0.2106 m. Its details report Each front width as 0.71 m and Total front face area as 0.74763 m². These are outputs for the single example entry set: five equal fronts, the stated outside face envelope, and the stated reveals and gap. They are arithmetic results for that layout.

For an American tape measure, the height is about 8.29 in and width about 27.95 in. The metric outputs are the calculator's reported values; the inch figures are rounded conversions for interpretation. Decide which units your shop drawings and measuring tools use, then carry enough precision through layout and mark the rounded cut dimension only after checking your material and fitting plan.

Check Width On Its Own

The width calculation is separate from the height division. Subtract both 9 mm outside side reveals from the 0.728 m envelope: 0.728 m minus 0.009 m minus 0.009 m equals 0.710 m. With fronts spanning the same opening, that is the width reported for each front. No internal vertical gap changes this width in the supplied arrangement.

Before using that result, decide whether your face envelope is measured between the same boundaries where the reveals will be judged. Account for any edge treatment or overlay convention in your project measurements rather than silently changing the calculator inputs. The arithmetic assumes the supplied face width and paired side allowances describe the intended visible layout; it does not define how the cabinet carcass is built.

Keep Boxes And Hardware Separate

A drawer front is the visible panel in this calculation. The result does not give the clear width or height of a drawer box, the box depth, slide length, or the clearance needed for hardware. Those dimensions require their own measurements and the specifications for the selected hardware, along with a fit check against the cabinet and neighboring parts.

Use the front result as one input to the next planning step. Confirm how the front attaches, where the box sits behind it, and whether the chosen hardware leaves the intended movement and clearances. Do not reduce the front dimensions by an assumed slide allowance; the calculator's reported front size follows the envelope and reveal arithmetic, while hardware fit is a separate documented property of the selected components.

Review The Stack Before Cutting

Lay out the calculated stack at full scale or mark its boundaries on a drawing. Five fronts at 0.2106 m each total 1.053 m; adding the 12 mm top reveal, four 14 mm gaps, and 16 mm bottom reveal returns the 1.137 m envelope. This back-check catches a missed gap or a reveal entered in the wrong place before the dimensions reach the shop.

If the real project uses unequal fronts, a different number of fronts, or another gap plan, this equal-front result no longer describes it. Re-enter the actual count and allowances rather than adjusting one front by eye. Recheck the outside face measurements after construction changes, and complete the separate box and hardware fit checks before committing to final cuts.

Questions about this guide

Why are there four gaps for five fronts?

Gaps occur between neighboring fronts. Five fronts have four neighboring pairs, so the example subtracts four 14 mm gaps.

Why are the top and bottom reveals different?

The example specifies 12 mm at the top and 16 mm at the bottom. Keep each allowance distinct unless your measured layout calls for different values.

Does 0.2106 m tell me the drawer-box height?

No. It is the calculated height of each visible front. Box dimensions and hardware clearances require separate measurements and fit checks.

What should I change if my cabinet is a different width?

Measure the new outside face width and enter that envelope with the intended reveal at each outside side. The example's 0.710 m front width applies only to its 0.728 m envelope and paired 9 mm side reveals.

Use the matching calculator

Updated . Reviewed . Methods and scope.

Related decisions

Connected work guides and comparisons

Browse all work types

Collect your material inputs

Browse material preparation sheets

Evaluate your own supplied alternatives

Browse quantity scenarios