SUPPLIED LAYOUT INTERVALS

Decorative full slat face stock — gap already supplied for the face scenarios.

How does changing gap already supplied for the face affect decorative full slat face stock when the other inputs stay fixed?

What this decision changes

The chosen interval or repeat changes discrete positions, full rows or complete pattern cuts. It is different from a blanket percentage added to area. Method basis: Full-width strips across each face = floor((width + supplied gap)/(slat face width + supplied gap)); continuous cuts retain measured height and cut extra. Does not predict sound absorption, choose gap, fire performance or supporting design.

The focus is gap already supplied for the face. All other shared inputs remain fixed for each evaluated range.

Full-width strips across each face = floor((width + supplied gap)/(slat face width + supplied gap)); continuous cuts retain measured height and cut extra.Decorative Full Slat Face Stock Calculator

Evaluate your supplied alternatives

Start with your measured plan and selected product data. The initial values and range are illustrative. Each scenario changes only gap already supplied for the face; the other entered values stay fixed.

Display units

Measured plan and product inputs

Selected stock length

Where to get this value

Use the actual usable quantity or dimensions of the product you intend to buy. Check the label and the unit shown here.

Your extra length reserved per cut

Selected slat face width

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Gap already supplied for the face

Measured decorative face 1

Measured face width

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Measured strip height

Where to get this value

Measure this dimension in your plan or on site and use the displayed unit. For irregular shapes, divide the geometry into the supported sections.

Identical faces

Supplied comparison range for gap already supplied for the face

Lower supplied comparison value

Upper supplied comparison value

Nine evenly spaced values are evaluated. Whole counts are rounded to distinct integer scenarios. Values between the listed samples are not calculated.

9 evaluated scenarios

Baseline: Slat stock lengths — 5 lengths. Rejected combinations remain visible below.

Quantity to plot

Each bar is one actual calculated slat stock lengths. Horizontal values: gap already supplied for the face in mm.

Gap already supplied for the face	Slat stock lengths	Change from baseline	Use this scenario
60 mm	6 lengths	1 lengths	Open in calculator Exact quantity breakdown Supplied face strips 6 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.
72.5 mm	6 lengths	1 lengths	Open in calculator Exact quantity breakdown Supplied face strips 6 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.
85 mm	5 lengths	0 lengths	Open in calculator Exact quantity breakdown Supplied face strips 5 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.
97.5 mm	5 lengths	0 lengths	Open in calculator Exact quantity breakdown Supplied face strips 5 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.
110 mm	5 lengths	0 lengths	Open in calculator Exact quantity breakdown Supplied face strips 5 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.
122.5 mm	5 lengths	0 lengths	Open in calculator Exact quantity breakdown Supplied face strips 5 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.
135 mm	4 lengths	-1 lengths	Open in calculator Exact quantity breakdown Supplied face strips 4 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.
147.5 mm	4 lengths	-1 lengths	Open in calculator Exact quantity breakdown Supplied face strips 4 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.
160 mm	4 lengths	-1 lengths	Open in calculator Exact quantity breakdown Supplied face strips 4 Continuous cuts use decreasing-length first-fit packing. This is a feasible count, not a guarantee of the minimum. Any per-cut extra is explicitly reserved by you. Only whole-width slats that fit are counted. Unfilled edge space is not assigned another trimmed slat. This is decorative quantity arithmetic, not acoustic performance.

Read the evaluated results

Use the evaluated count steps to see when another row, column, drop or position enters the stated layout.

Replace every illustrative baseline measurement and selected product value with the inputs for your actual task.
Enter a comparison range on the focused input's stated unit and quantity basis.
Review rejected combinations and use the exact detail lines to distinguish measured demand from whole purchases.
Open an evaluated scenario in the full calculator to save its original inputs and quantity breakdown to a browser material project.

Keep the comparison within scope

Compare intervals already permitted by your plan or product. No safe spacing, structural layout or fixing requirement is chosen.

Does not predict sound absorption, choose gap, fire performance or supporting design.

Only the listed samples are evaluated. Intermediate values, alternate constraints and global cutting optimality are not inferred from the graph.

Continue with this quantity method

Decorative Full Slat Face Stock Calculator

Other independent input decisions

Prepare the actual material data

Read the measurement and purchase guides

Quantity method and illustrative scenarios checked 6 October 2026. Methods and scope.