How to measure and order: decorative panels, fabric covers and supplied attachment counts.
Publication and review
- Author
- Metandum Team
14 years of experience in digital web projects.
- Reviewer
- Metandum Team
14 years of experience in digital web projects.
- Published
- Last reviewed
- Last updated
Start with a product and layout record
A panel order depends on measured dimensions, the selected decorative layout and the stock format that will supply each piece. Keep the product code and drawing revision with every quantity so a later change in size or finish does not carry the previous order forward unnoticed. The linked calculators cover specific arithmetic tasks: slat strips across a face, perforation geometry, covered-panel blanks, coating, supplied staple positions and masking discs. Their outputs apply only to the inputs shown. They do not choose an acoustic rating, fire performance, attachment schedule or masking material. Separate those requirements into the product documentation before using quantity results to prepare a purchase list. Reconcile drawing dimensions and calculator units before transferring values into an order form. Mark each line with its source.
Confirm the named acoustic product
The cited acoustic-panel product page identifies the standard panel’s listed acoustic values as NRC 0.70 and CAC 40 dB, and gives typical sizes of 600 × 600 × 19 mm and 1200 × 600 × 19 mm. A separate panel variant is listed with NRC 0.90 and CAC 29 dB. Those are manufacturer-reported details for named product variants, not values calculated by the quantity tools. Record the exact model and current data sheet rather than transferring one variant’s label to another panel. The page also links installation and cleaning documents; use those documents for product-specific handling and assembly details. Verify the exact model code on the quoted carton because regional listings may differ. Do not assume every outlet stocks both sizes.
Measure complete face positions
Count the selected decorative faces from the drawing and measure their usable widths and heights. In the supplied slat example, a 1 m face is paired with 0.1 m face slats and a supplied 0.1 m gap. The calculator returns five full-width strips for that face. At a 2 m measured strip height, each strip needs a 3 m stock length, so the order is five lengths. The check runs the one-face input through the slat stock calculator. This is an example of supplied dimensions, not a recommended slat width or spacing. Add any distinct end pieces as separate runs instead of assuming every face has the same geometry. Keep repeated faces on separate rows when their heights or quantities vary. Recheck stock when the cut allowance changes.
Keep perforation geometry literal
For a perforated panel, enter the gross measured panel width and height, hole diameter, non-overlapping hole count, thickness and supplied material density. The calculator reports geometric open percentage, retained area and retained mass from those values. It does not determine acoustic absorption, ventilation flow, fire performance or panel strength. Its worked example uses a 1 m square panel with ten 0.1 m holes and a specified thickness and density; the open percentage is about 7.85%. Treat that as a geometry example only. A real product may have a different hole pattern, edge margin or support condition, so obtain its measured dimensions and material specification before using this calculation. Open percentage alone cannot describe the remaining web layout or edge reinforcement. Check the actual hole schedule before entry.
Add side depth and back return
A covered face blank can extend beyond the visible panel dimensions to wrap the side and return to the back. The wrap calculator adds twice the supplied depth and back-return margin to each face dimension, then fits the resulting rectangles to the stated stock size. An independent two-panel example uses 0.45 m square faces, 0.03 m depth and 0.02 m return. Each complete blank becomes 0.55 m square, and both blanks fit on one 1 m by 2 m stock sheet in the fixed orientation. The output is a rectangular allocation with the supplied gap and rotation settings; it does not select fabric tension, seam placement or attachment method. Confirm whether fabric stock has a usable width smaller than the nominal roll width. Include a cutting gap only when the plan specifies one.
Separate coating area from containers
A coating estimate needs the number of coats, selected product coverage, container volume and the faces or edges already specified for each baffle. The calculator totals only the chosen broad faces, narrow faces and ends. Its example enters three baffles, coats two broad faces on each, and uses the stated coverage and container size; the engine returns three containers for 3 m² of measured coated area. These supplied example inputs are not a recommendation for a coating system or a performance claim. If a panel has additional returns, select those surfaces in a separate measured model where available. Never infer coverage from the product name; use the current manufacturer label. Keep the number of coats consistent with the chosen specification. Verify whether the stated spread rate assumes one coat or the full system.
Count only an established attachment pattern
The staple-pack tool converts a supplied pitch, staples per position and selected pack size into a pack count for rectangular frames. In the example, four 0.5 m by 1 m frames use a 0.1 m pitch, one staple at each position and 100 staples per pack; the result is two packs. That arithmetic follows the entered pattern. It does not say that this spacing or fastener is suitable for a decorative panel, a fabric tension or a particular support. Use it only when an approved plan already defines the frame dimensions and attachment positions. Keep the resulting pack line separate from panels, sheet stock and finish materials. The tool counts perimeter positions according to its entered pitch. The plan, not the calculator, sets that pitch.
Keep orders separated by material
A complete order may include face stock, wrap fabric, coating, frame staples and perforation masks. Each uses a different unit and calculation, so keep them on separate lines with a source label and package basis. Do not add alternative face-only and wrapped-panel scenarios together; choose the actual construction and retain the other scenario only as a comparison. Check usable stock dimensions, permitted rotation, reserved cutting gap and whole-package rounding against the supplier information. If a product variant or layout changes, recalculate the affected item and leave unrelated quantities intact. The calculators provide reproducible arithmetic from supplied inputs; the documented product and project specification govern suitability. This format makes exclusions visible before a quote is accepted. Keep supplier quotes adjacent to their corresponding line items.
Questions about this guide
Are the acoustic values in the article calculator outputs?
No. The cited manufacturer page lists NRC 0.70 and CAC 40 dB for one standard panel and NRC 0.90 and CAC 29 dB for a separate variant. Match values to the exact product model; quantity tools do not calculate acoustic performance.
What does the slat-face example return for one panel?
A 1 m face with supplied 0.1 m slat width and 0.1 m gap takes five strips. The 2 m height and 3 m stock setting establish the order lengths in this example; they are not recommended slat dimensions or spacing.
What open area does the perforation example calculate?
Ten 0.1 m holes in a 1 m square panel yield about 7.85% geometric open area. That calculation describes hole geometry and retained material, not acoustic absorption, ventilation flow, fire performance, or panel strength.
Why keep wrapped blanks, coating, and staples on separate order lines?
They use different units and models: sheet allocation for wrapped blanks, measured surface coverage for coating, and a supplied frame pitch and pack size for staples. Keep each quantity tied to its own selected material, face count, or approved attachment plan.
Use the matching calculator
Updated . Reviewed . Methods and scope.